How Much Is It To Clear A Wooded Lot

Covering our deck has been on the to-do list since last year when we refinished our old deck with new paint and stain. For this project we built a DIY covered pergola attached to the house and attached to our existing deck. We then covered the DIY pergola with clear corrugated plastic roofing sheets to create a dry, sunny, outdoor living space. Here is the complete DIY tutorial for building a clear corrugated covered pergola attached to the house and an existing deck!

Before & After Photos

On the left you can see the deck before we stained and painted it followed by the deck before we added the DIY pergola. The photo on the right shows the deck with the finished pergola.

Are you ready for the tutorial? First we had to rip out that arbor. After that we were ready to begin. Here is the complete DIY covered pergola tutorial!

Tools:

Circular Saw
Drill
Right angle drill with 5/8″ x 16″ auger bit

Step 1: Build the Pergola

First you will need to install your vertical supports and your horizontal beam. Just make sure you won't need to be replacing your roof anytime soon before you begin! It always makes sense just to check that the structure around the supports is solid. Just a quick examination of the surroundings ought to be enough. You could tear out your existing deck supports and use a solid support however, we opted to extend the existing supports using a bracket. As far as wood goes, you can use pressure treated wood or cedar. Pressure treated wood is much cheaper, and comes in in either incised or non-incised. We opted for non-incised (though its slightly more expensive than incised) on all the pieces except the beam (because it wasn't available in our area) and then wrapped the beam in 1×6″ cedar to hide the incisions.

Supplies:

Post support brackets for 4×4″ wood (2)
4×4″ vertical wood supports (2) we cut a 10′ beam in 1/2 and used 5′ lengths to reach our desired height of 8′ at the end of our pergola
4×6″ horizontal support beam (1) we used a 16′ beam, the width of our deck
2×6″ plank of wood to attach to the house as the ledger (1) we used a 16′ long plank
2×4″ wood joist slats (9) we used 12′ long wood slats, spaced 24″ apart spanned across our 16′ wide deck (we used 9 total)
2×4″ wood – 8′ length (2) we used these to add additional support to the vertical 4×4″ supports
2-in x 4-in 18-Gauge Triple Zinc Face Mount Joist Hanger – to attach the wood slats to the house (9) you will need one for each wood slat you attach to the house
5-2/7-in 18-Gauge Triple Zinc Steel Rafter Tie Brackets – to attach joist slats to the horizontal support beam (9) you will need one for each wood slat you attach to the beam
5″ ledger board fastener, 5/16″ hex head coated (7) use as many as you feel necessary, we used 7, spaced 24″ apart
8″ lag bolts (4)

Cut existing caps off where the vertical supports will be attached

Note that we simply screwed the beam into the 4×4″ supports using 8″ lag bolts (2 per post) to secure their attachment. The temporary supports are to hold this structure in place until it is secured to the house.

After the supports and beam are in place, you can work on attaching it to the house. We used a 16′ long 2×4″ piece of wood which we attached to the house with lag bolts, and then spaced 9x 12′ long 2×4″ slats spaced 24″ apart. No siding was removed – the bolts are strong enough to go through the siding and into the framing. We selected this height for our ledger because it is in line with the ceiling, where we know there would be wood framing to support the attachment of the roof.

Attach your wood joist slats to the house with ledger fastners

Step 2: Install the Clear Corrugated Roof

Next, you will install the wood roof supports on top of the wood slats and then install the clear corrugated roof on top of these roof supports. As far as painting goes, you should at least paint the wood roof supports before installing them because once the roof is attached it will be very hard to paint, and impossible to paint the top (which you can see from above).

Supplies:

Corrugated roof panels (8) we used 8x 26″ wide panels at 12′ lengths from Home Depot (Palruf brand – 26 in. x 12 ft. Clear PVC Roofing Panel)
Horizontal plastic closure strips, packs of 6 (8) we used 8 packs of 6 to cover our 4 roof supports at 16′ long each support
2×2″ wood roof supports (4) we used 8x 8′ lengths, but you could use 4x 16′ lengths, or whatever length you need for your project to at least create 4 roof supports across the top
1.5″ Decking screws (100)
1.5″ Fastener Screws (100)

Place your 2×2″ wood roof supports on top of the wood slats, spacing evenly. We did 3.5′ spacing

Step 3: Paint

We used the same paint that we previously painted the deck, which is easy to paint on, and durable for outdoor projects: Glidden Premium Exterior Paint, satin, white. We used a combination of rollers and brushes, making sure our deck was covered with drop cloths as we worked. The painting itself took nearly a whole day.

The Finished Project

It is so nice to have a DIY covered pergola with a clear corrugated roof. Now the relentless Seattle rain won't stop us from enjoying our outdoor space year round! This DIY project only took us 3 days start to finish, and was fairly straightforward. I hope this helps you on your own DIY pergola and clear corrugated roof installation!

Answers to some of my readers questions:

This project cost us approx. $800, though we already owned all the power tools
Our deck is 16′ wide and 10′ deep
The roof is Palruf brand, we found it at Home Depot
We did not remove any siding, we attached the ledger directly into the siding of the house
The height from the deck to the top of the ledger on the house is 9′ which creates about a 1′ difference from the house to the edge of the pergola, and it is perfect for the slope to keep the rain draining properly (even in the heavy rain we see in Washington)
The edge of the corrugated plastic roof hangs over the last support just slightly to line up with the edges of our house, which is slightly farther out than the deck railing – it was simply a matter of aesthetic preference when we did this – we actually plan to add more roofing even farther out to protect against the rain dripping off the edge onto the deck
The support slats for the roofing are spaced approximately 24″ apart. We centered the first one and then spaced out evenly on either side except for the last support on one side which had to be slightly closer to line up with the ledger at about 22″ (the farthest part of the house we could attach it to) We wanted them as even as possible, and the outside slats to line up with the deck railing
We did 4 cross supports, we could have added more or done less, we just guessed and so far it seems like the perfect amount of space
This project cost us around $800 for wood, roofing, paint and all materials – we already owned the tools
We have had it for a year and so far no leaks or holes
It does need to be gently sprayed off at least yearly because of the moss from our second floor gutter that drops on it
We had 2 weeks of heavy snow over the past year and it did not damage the pergola

Shop this post: